The line Brush
Draw a line
The number and the thickness of the line change by the pressure
The Brush!
Monochrome Layer Only
* This will be the same as the dynamic line brush distributed to FANBOX's supporters.
Multi-line Brush
-Moving Line Brush Small
It is set of two.
Such a line is closed to shine!
I can draw a curve, but I cannot draw a sharp curve.
Snap to ruler can also be drawn!
▼ Parallel Line Ruler
Concentric ruler
The brush tip image is made up of a point rather than a line like an image.
It controls the line width by changing the density of the line with pressure.
It is hard to put out the Caspar line of the pressure weakness . You may need a little getting used to it.
※ Depending on the pressure of the individual "there is no Caspar line at all!" I think that there is a case that. If so, adjust the settings of pen pressure ! Please check below to learn how to set up ^ ^
◆ How to adjust settings of pen pressure
If you draw a light touch and nothing is drawn, and you can't get a line, try increasing the number of brush density first.
I adjust the settings of pen pressure when the ink doba when I raise it now.
Clicking the icon next to the number in the brush density will bring up the settings of pen pressure graph.
The bottom left curve is the pressure light setting.
If the curve is Sagere, the line becomes thin if the line becomes thick, and it is lower.
If the line is not drawn when the light pressure is drawn, try adjusting the curve slightly above the lower left side.
It is set so that the line is close to a thick and solid when I draw a strong pressure, but if I do not want to make it solid, set the pressure strength and lower the curve on the center of the graph to the right.
The LEG line is the default interval.
If you want to make gap of line smaller , try lowering the brush size.
In that case, please raise ' brush density ' because the reduce brush size and the line become thin.
* I want to revert to the original setting. If this is the case, open the tool property ' sub tool detail ' and select ' Reset all settings to default ' .
* I want to save the adjusted settings! If so, select 'register to initial settings all settings '. (If you register to initial settings all settings, you cannot revert to the previous setting.)
動線ブラシは
『引いた分だけ線が引ける』
『筆圧で線の多さ・太さが変化する』
ブラシです！
モノクロレイヤー専用
※FANBOXの支援者向けに配布している動線ブラシと同じものになります。
・動線ブラシ多
・動線ブラシ少
の２種セットです。
このような線がシャシャシャっと引けます！
カーブは描けますが、急カーブは描けません。
定規にスナップさせて描くこともできます！
▼平行線定規
▼同心円定規
ブラシ先端画像は▼画像のように線ではなく点で構成されています。
筆圧で線の濃度を変化させて、線の太さをコントロールしています。
筆圧弱めのカスレ線は出しにくいです。少し慣れが必要かもしれません。
※個人の筆圧によっては「カスレ線が全然出ないよ！」という場合もあると思います。その場合は筆圧設定を調整してください！設定の仕方は下記をご確認ください＾＾
◆筆圧設定の調整の仕方
「軽いタッチで描いても何も描画されない」「カスレ線が出せない」という場合、まずは『ブラシ濃度』の数値を上げてみてください。
上げたら今度はインクがドバっと出ちゃうという場合は筆圧設定を調整します。
『ブラシ濃度』の数値の横にある『↓』アイコンをクリックすると筆圧設定のグラフが出てきます。
左下の曲線が筆圧軽めの設定になります。
曲線を上にあげれば線は太くなって、下にさげれば線は細くなります。
筆圧軽めに描いた時に線が描画されない場合は、左下側の曲線を少し上に調整してみてください。
筆圧を強く描いたときに線が太くベタに近くなるように設定していますが、ベタにしたくない場合は筆圧強めの設定、グラフの中央～右側の曲線を下にさげてください。
足の動線がデフォルト設定の間隔になります。
線の間隔をもっと狭くしたい場合は『ブラシサイズ』を下げてください。
ブラシサイズを下げると線が薄くなるので、その場合は『ブラシ濃度』を上げてください。
※設定を「元の設定に戻したい！」という場合は、ツールプロパティの『サブツール詳細』を開いて『全設定を初期設定に戻す』を選択してください。
※「調整した設定を保存したい！」という場合は、『全設定を初期設定に登録』を選択してください。（全設定を初期設定に登録すると、その前の設定には戻せません）
Line Brush 動線ブラシ
Other materials by 聖月
Popular “Material catalog” materials
New materials
Badges
-
MVP ◆This user has contributed greatly to the management of the community, by posting many great responses to the questions asked. Once every three months, MVPs are determined based on the points earned during that period and will be recognized accordingly. -
New Valuable Player (NVP) ◆These are the next-best contributors to the community after MVPs. This is awarded to users who have not yet won an MVP award, based on the number of points they have earned. -
Official Expert ◆Chosen out of all MVP awardees, who are already proof of excellence, this is a testimony of outstanding correspondence in the community. After careful screening, they are appointed by CELSYS and assume their position.Note: Formally called “Evangelists” -
Official Moderator of CELSYS ◆Moderators are official CELSYS staff members who are fluent in Japanese as well as various other languages. Moderators are not experts on the software or illustration, so they are not able to directly answer your questions. However, moderators provide communication and language support to ensure that everyone can smoothly communicate with each other. -
CELSYS official accountThe Official Administrator Account