Slide, gym, swing (indoor playground equipment) (滑り台・ジム・ブランコ（屋内遊具）) 滑り台・ジム・ブランコ（屋内遊具）
Content ID：2310818
-
1,805
This is an indoor playground equipment for young children made of white resin pipes and mint fittings. A 3-in-1 with a swing on the left and a jungle gym and slide on the right. The installation dimensions are approximately 1,850 × 1,300 mm, and the overall height is 800 mm. The jungle gym is a three-tier lattice. The deck is on the right, and the top is open. At the back of the deck is a 45-degree staircase built with the same pipe as the frame, and in the foreground is a slide. It is a flow line that goes up and slides down as it is. The seat of the swing is bucket-shaped with a backrest and a front bar, and there are two holes for passing the foot in front of it, and it is divided into left and right by a crotch divider. Each hanging tool has one object, and the origin is on the horizontal mounting material. If you turn it around the X axis, it becomes a pendulum with the suspension point as the fulcrum. Comes in 4 angles. 白い樹脂パイプとミントの継手でできた幼児用の室内遊具です。左にブランコ、右へジャングルジムと滑り台が並ぶ3in1。設置寸法は約1,850×1,300mm、全高800mm。ジャングルジムは3段の格子。右にはデッキが載り、その上は開けてあります。デッキの奥には枠と同じパイプで組んだ45度の階段、手前には滑り台。上ってそのまま滑り降りる動線です。ブランコの座面は背もたれと前バーの付いたバケット型で、手前に足を通す穴が2つ、股の仕切りで左右に分かれています。吊り具ごと1つのオブジェクトで、原点は横架材の上。X軸まわりに回せば吊り点を支点にした振り子になります。4アングル入り。
About this material
It is an indoor playground equipment with a swing, jungle gym, and slide in one frame. It has a total height of 800 mm and an installation dimension of approximately 1,850×1,300 mm.
Slides
There is a staircase at the back of the deck and a slide in front. It is a flow line that slides up and down without changing direction.
How to swing a swing
The seat surface is one object for each lifting tool, and the origin is on the horizontal mounting material. When the swing seat is turned around the X axis, it becomes a pendulum with the suspension point as the fulcrum.
The seat is a bucket type for infants. It is 340 × 260 mm and has two holes (about 100 mm wide) for passing the foot in front, a crotch partition between them, and a bar in front. With backrest.
4 angles
Four items are registered: front, back, right, and left.
LT Conversion
Below is the main line converted to LT with the actual CLIP STUDIO machine.
Specifications
- Installation dimensions Approx. 1,850 × 1,300mm / Height 800mm
- Jungle gym: 3 tiers (300, 550, 800mm) / 3 lattice on the back left, 1 lattice on the front left
- Deck 560 × 480mm, height 344mm (top is open. 550mm handrail only on the right edge)
- 2 stairs (115/229mm) / 2 45-degree diagonal timbers at the back of the deck with the same pipe as the frame
- Slide: Total length 820mm, width 460mm, width 460mm, 344mm→20mm (from right edge to front / same direction as the swing)
- Swing horizontal mounting material 675mm (middle of the third tier), seat surface 170mm, seat to horizontal mounting material 460mm
- Seat 340 × 260 mm, 2 holes for passing legs (about 100 mm wide), with crotch partition and front bar
- Fulcrum: The swing seat is on the horizontal mount (swings when turned around the X axis)
- 4 angles (front, back, right, left)
- Origin: Center of the ground plane / Front: −Y direction
この素材について
ブランコ・ジャングルジム・滑り台が1つの枠に入った室内遊具です。全高800mm、設置寸法は約1,850×1,300mm。
滑り台
デッキの奥に階段、手前に滑り台が付きます。上って向きを変えずにそのまま滑り降りる動線です。
ブランコの振らせ方
座面は吊り具ごと1つのオブジェクトで、原点が横架材の上にあります。ブランコ座席 をX軸まわりに回すと、吊り点を支点にした振り子になります。
座面は幼児用のバケット型。340×260mmで、手前に足を通す穴が2つ（幅約100mm）、そのあいだに股の仕切り、前にはバーが付きます。背もたれ付き。
アングル4件入り
正面・背面・右・左の4件を登録してあります。
LT変換
下はクリスタの実機でLT変換した主線です。
仕様
- 設置寸法 約1,850 × 1,300mm／全高800mm
- ジャングルジム：3段（300・550・800mm）／奥左が3段の格子・手前左は1段
- デッキ 560 × 480mm・高さ344mm（上は開放。右端だけ550mmの手すり）
- 階段 2段（115・229mm）／デッキの奥に枠と同じパイプで45度の斜材を2本
- 滑り台 全長820mm・幅460mm・344mm→20mm（右端から手前へ／ブランコと同じ向き）
- ブランコ 横架材675mm（3段目の中ほど）・座面170mm・座面から横架材まで460mm
- 座面 340 × 260mm・足を通す穴2つ（幅約100mm）・股の仕切りと前バー付き
- 支点：ブランコ座席 は横架材の上（X軸まわりに回すと振れる）
- アングル4件（正面・背面・右・左）
- 原点：接地面の中心／正面：−Y方向
Material マテリアル
-
default material 初期マテリアル
Configuration 配置
-
default layout 初期レイアウト
Angle アングル
-
Front 正面
-
The backside 背面
-
Right 右
-
Left 左
Update history
2026/10/4 Material review (improvement of accuracy, addition of materials, clarification of contour lines), registration of angles
2026/10/4 素材見直し（正確性向上、マテリアル追加、輪郭線の明確化）、アングルの登録
Old version
Other materials by Didymoi.A
Popular “3D object” materials
-
Plan Bonus
New materials
-
MVP ◆This user has contributed greatly to the management of the community, by posting many great responses to the questions asked. Once every three months, MVPs are determined based on the points earned during that period and will be recognized accordingly. -
New Valuable Player (NVP) ◆These are the next-best contributors to the community after MVPs. This is awarded to users who have not yet won an MVP award, based on the number of points they have earned. -
Official Expert ◆Chosen out of all MVP awardees, who are already proof of excellence, this is a testimony of outstanding correspondence in the community. After careful screening, they are appointed by CELSYS and assume their position.Note: Formally called “Evangelists” -
Official Moderator of CELSYS ◆Moderators are official CELSYS staff members who are fluent in Japanese as well as various other languages. Moderators are not experts on the software or illustration, so they are not able to directly answer your questions. However, moderators provide communication and language support to ensure that everyone can smoothly communicate with each other. -
CELSYS official accountThe Official Administrator Account