Iron bar (outdoor use, with auxiliary plate) (鉄棒(屋外用・補助板付き)) 鉄棒(屋外用・補助板付き)

Content ID:2311714

  • 1,261
  • Free
This material can be used in Studio Mode. (What is Studio Mode?)

It is an outdoor iron bar to be installed in schools and nursery schools. Three pillars are erected in a row, and a bar with a height of 1,000 mm and 800 mm is passed between them. The middle support receives both bars. The upside down auxiliary board was placed at the back of the bar. You can run up with your feet while holding the bar. All 3 posts, 2 bars, and 2 auxiliary plates are object separately. You can also create a state of only the high side and only the low side. The origin is the center of the contact patch, and the bar is in the X direction. Includes 4 angles: front, back, right, and left. 学校や保育園に据え付ける屋外用の鉄棒です。支柱3本を一列に立て、あいだに高さ1,000mmと800mmのバーを渡した連結式。真ん中の支柱が両方のバーを受けます。逆上がり補助板はバーの奥に置きました。バーを握ったまま足で駆け上がれます。支柱3本・バー2本・補助板2枚はすべて別オブジェクトです。高い方だけ・低い方だけの状態も作れます。原点は接地面の中心、バーはX方向。正面・背面・右・左の4アングル入り。

About this material

It is an outdoor iron bar with 3 posts and 2 bars. The heights are 1,000 mm and 800 mm. Comes with a side-down auxiliary plate.

It is a concatenated type

Three supports are arranged in a row, and the middle one receives both the left and right bars. The two iron bars are not placed separately, but stand as a continuous facility. Since each pillar is object separately, it can be reduced to only the higher and lower ones.

  • Tube: φ90, spacing 1,600mm, ivory
  • Bar: φ34, galvanized color. Clasp is green

Inverted auxiliary board

The end of the bar side is a curve that rises towards the back of the bar. It's that board that runs up with your feet while holding the bar.

4 angles

Four items are registered: front, back, right, and left.

LT Conversion

Below is the main line converted to LT with the actual CLIP STUDIO machine.

Specifications

  • 3 pillars (φ90, spacing 1,600 mm, 1 object separately) / bar φ34, height 1,000 mm and 800 mm
  • Auxiliary plate: width 620mm, 15 horizontal plates (5 blue, 5 yellow, 5 red), curved curved surface, blue side plate and steel pipe frame
  • Rubber mat 4,800 × 2,600 × 40mm (3,200mm wide for single version)
  • 4 angles (front, back, right, left)
  • Origin: Center of the contact patch / Bar: X direction / Support plate: Curve rising to the back of the bar (+ Y side / back)

この素材について

支柱3本・バー2本の連結式の屋外鉄棒です。高さは1,000mmと800mm。逆上がり補助板が付きます。

連結式になっています

支柱3本が一列に並び、真ん中の1本が左右両方のバーを受けます。2本の鉄棒を別々に置いたのではなく、ひと続きの設備として立っている形です。支柱は1本ずつ別オブジェクトなので、高い方だけ・低い方だけに減らせます。

  • 支柱:φ90、間隔1,600mm、アイボリー
  • バー:φ34、亜鉛メッキの色。留め金具は緑

逆上がり補助板

バー側の端は地面すれすれで、奥へ向かってせり上がるカーブです。バーを握ったまま足で駆け上がる、あの板です。

アングル4件入り

正面・背面・右・左の4件を登録してあります。

LT変換

下はクリスタの実機でLT変換した主線です。

仕様

  • 支柱3本(φ90・間隔1,600mm・1本ずつ別オブジェクト)/バー φ34・高さ1,000mmと800mm
  • 補助板 幅620mm・横板15枚(青5・黄5・赤5)・カーブした曲面・青い側板と鋼管の枠
  • ゴムマット 4,800 × 2,600 × 40mm(単体版は3,200mm幅)
  • アングル4件(正面・背面・右・左)
  • 原点:接地面の中心/バー:X方向/補助板:バーの奥(+Y側・奥へ立ち上がるカーブ)

Material マテリアル

  • default material 初期マテリアル

Configuration 配置

  • default layout 初期レイアウト

Angle アングル

  • Front 正面
  • The backside 背面
  • Right 右
  • Left 左

Update history

2026/10/7 Material review (accuracy improvement, material addition, outline line clarification), angle registration 2026/10/7 素材見直し(正確性向上、マテリアル追加、輪郭線の明確化)、アングルの登録

Old version

Content ID:2311714

Published : 8 hours ago

Last updated : 8 hours ago

Didymoi.A's profile Go to profile

興味をもっていただきありがとうございます! 私は漫画家をやっています。漫画で利用する素材などをBlenderを使って作成しています。たくさんアップしますのでフォローお願いします。Xでも制作過程を乗せていますのでフォローやいいねなど反応していただけると嬉しいです。また仲良くしていた方限定で制作要望を承る場合がありますのでダイレクトメッセージください。