Plank crossing bridge (log sleepers) (板の渡り橋(丸太の枕木)) 板の渡り橋(丸太の枕木)

Content ID:2310666

  • 1,015
  • Free
This material can be used in Studio Mode. (What is Studio Mode?)

It is a low crossing bridge with planks lined up on log sleepers. The total length is about 4.5 m, and the top of the board is about 255 mm. Each of the three sections bends at a slightly different angle, so you can't walk straight. All the corners of the board are also rounded. At the starting point, there is a step platform made of logs, from which you can climb and start crossing. The head of the mounting bolt is also inserted. The origin is the center of the contact patch, and the crossing direction is generally in the X direction. 4 angles are registered. 丸太の枕木の上に板を並べた、低い渡り橋です。全長およそ4.5m、板の天端は約255mm。3つの区間がそれぞれ少しずつ角度を変えて折れ曲がるので、まっすぐには歩けません。板の角もすべて丸めてあります。始点には丸太を組んだ踏み台が付き、そこから上って渡り始めます。取り付けボルトの頭も入れてあります。原点は接地面の中心、渡る向きはおおむねX方向です。4アングルを登録してあります。

About this material

It is a low crossing bridge with a total length of 4.5 m and a top of 255 mm. Each of the three sections is bent at a different angle.


3 broken sections

It is not a straight one, but changes direction for each section. When viewed from directly above, it becomes a shallow zigzag, so the direction of the person crossing changes from frame to frame.

Planks and sleepers

The crossing boards are lined up one by one, and the joints come out as lines. It is 420 mm wide and all corners are rounded. A log sleeper is placed on the ground, on which two girders are threaded to receive boards. The board is bolted directly above the girders. At the joint enters the head of the bolt.

4 angles

Four items are registered: front, back, right, and left.

LT Conversion

Below is the main line converted to LT with the actual CLIP STUDIO machine.


Specifications

  • Overall length: approx. 4,500 mm, crossing board: width 420 mm, top edge: approx. 255 mm (one piece at a time)
  • 3 sections (different angles) / Springboard (wood mouth is tree ring material)
  • How to assemble: 3 log sleepers per section / 2 girders on them to receive boards
  • With bolt head
  • 4 angles (front, back, right, left)
  • Origin: Center of the ground patch / Direction of crossing: Approximately X direction

この素材について

全長4.5m、天端255mmの低い渡り橋です。3区間がそれぞれ角度を変えて折れています。


折れた3区間

まっすぐな1本ではなく、区間ごとに向きが変わります。真上から見ると浅いジグザグになるので、渡る人物の向きがコマごとに変わります。

板と枕木

渡り板は1枚ずつ並べた張りで、目地が線として出ます。幅420mm、角はすべて丸めてあります。地面に丸太の枕木を置き、その上に桁を2本通して板を受けています。板は桁の真上でボルト留め。つなぎ目にはボルトの頭が入ります。

アングル4件入り

正面・背面・右・左の4件を登録してあります。

LT変換

下はクリスタの実機でLT変換した主線です。


仕様

  • 全長 約4,500mm/渡り板 幅420mm・天端 約255mm(1枚ずつの張り)
  • 3区間(それぞれ角度が違う)/踏み台(木口は年輪マテリアル)
  • 組み方:区間ごとに丸太の枕木3本/その上に桁2本を通して板を受ける
  • ボルトの頭入り
  • アングル4件(正面・背面・右・左)
  • 原点:接地面の中心/渡る向き:おおむねX方向

Material マテリアル

  • default material 初期マテリアル

Configuration 配置

  • default layout 初期レイアウト

Angle アングル

  • Front 正面
  • The backside 背面
  • Right 右
  • Left 左

Update history

2026/10/7 Material review (accuracy improvement, material addition, outline line clarification), angle registration 2026/10/7 素材見直し(正確性向上、マテリアル追加、輪郭線の明確化)、アングルの登録

Old version

Content ID:2310666

Published : 2 hours ago

Last updated : 2 hours ago

Didymoi.A's profile Go to profile

興味をもっていただきありがとうございます! 私は漫画家をやっています。漫画で利用する素材などをBlenderを使って作成しています。たくさんアップしますのでフォローお願いします。Xでも制作過程を乗せていますのでフォローやいいねなど反応していただけると嬉しいです。また仲良くしていた方限定で制作要望を承る場合がありますのでダイレクトメッセージください。