Guardrail (3 spans, 12m) (ガードレール(3スパン・12m)) ガードレール(3スパン・12m)

Content ID:2310646

  • 590
  • Free
This material can be used in Studio Mode. (What is Studio Mode?)

It is a guardrail along the road. There are four pillars at intervals of 4 m, a height of 600 mm, and a total length of 12 m. The origin is at ground level at the center of the whole area, and the road side is in the −Y direction. Four angles are registered: front, back, right, and left. 道路沿いのガードレールです。支柱を4m間隔で4本、高さ600mm、全長12mにしてあります。原点は全体の中心の地面レベル、道路側は−Y方向です。正面・背面・右・左の4アングルを登録してあります。

About this material

It is a guardrail with a total length of 12 m and 4 pillars. Since the 4m span × 3 is made into one unit, it can be seamlessly extended by duplicating 12,000 mm in the X direction. The two photos below are the angles registered for this material.

Cross-section of a corrugated beam

The guardrail is a W-shaped cross-section with a single ridge in the center.

  • The central ridge and the upper and lower edges, a total of five ridge lines run in the longitudinal direction.
  • The ends are closed with an obliquely squeezed cap. I can't see the cut mouth
  • A bolt and washer are attached to the central ridge for each position of the post.

Around the pillars

The pillar is a φ140 round pipe. The beam is not directly attached to the support, but is extended 60 mm in front of the bracket. When viewed from the road side, there is a single shadow line between the beam and the support. The posts are equipped with reflectors.

4 angles

Four items are registered: front, back, right, and left. You can choose from tool property (sub tool detail "Camera" → "Angle").

LT Conversion

Below is the main line converted to LT with the actual CLIP STUDIO machine.

Specifications

  • Overall length 12,000mm (effective 4,000mm × 3 spans) / Pillar φ140 @4,000mm × 4 pcs
  • Beam center height 600mm/W cross-section (with folded thickness) with end cap
  • Bracket (beam 60mm forward from the column), bolts and washers, reflector
  • 4 angles (front, back, right, left)
  • Origin: Ground level of the entire center / Road side: −Y direction

この素材について

全長12m・支柱4本ぶんのガードレールです。4mスパン×3 を1単位にしてあるので、X方向へ12,000mmずつ複製すれば継ぎ目なく延ばせます。下の2枚は、この素材に登録してあるアングルです。

波形ビームの断面

ガードレールは中央に1本の稜が通ったW形の断面です。

  • 中央の稜と上下の縁、合わせて5本の稜線が長手方向に走ります
  • 端部は斜めに絞ったキャップで塞いであります。切りっぱなしの口が見えません
  • 中央の稜にボルトと座金が、支柱の位置ごとに付きます

支柱まわり

支柱はφ140の丸パイプ。ビームは支柱に直付けせず、ブラケットを挟んで60mm手前に出してあります。道路側から見たとき、ビームと支柱のあいだに影の線が1本入ります。支柱には反射板が付きます。

アングル4件入り

正面・背面・右・左の4件を登録してあります。ツールプロパティ(サブツール詳細の「カメラ」→「アングル」)から選べます。

LT変換

下はクリスタの実機でLT変換した主線です。

仕様

  • 全長 12,000mm(有効4,000mm × 3スパン)/支柱 φ140 @4,000mm × 4本
  • ビーム中心高さ 600mm/W断面(板厚ぶんの折り返しあり)・端部キャップ付き
  • ブラケット(ビームを支柱から60mm前出し)・ボルトと座金・反射板
  • アングル4件(正面・背面・右・左)
  • 原点:全体の中心の地面レベル/道路側:−Y方向

Material マテリアル

  • default material 初期マテリアル

Configuration 配置

  • default layout 初期レイアウト

Angle アングル

  • Front 正面
  • The backside 背面
  • Right 右
  • Left 左

Update history

2026/10/3 Material review (accuracy improvement, material addition, outline line clarification), angle registration 2026/10/3 素材見直し(正確性向上、マテリアル追加、輪郭線の明確化)、アングルの登録

Old version

Content ID:2310646

Published : 1 hour ago

Last updated : 1 hour ago

Didymoi.A's profile Go to profile

興味をもっていただきありがとうございます! 私は漫画家をやっています。漫画で利用する素材などをBlenderを使って作成しています。たくさんアップしますのでフォローお願いします。Xでも制作過程を乗せていますのでフォローやいいねなど反応していただけると嬉しいです。また仲良くしていた方限定で制作要望を承る場合がありますのでダイレクトメッセージください。