Bowl 01 diameter approx. 13cm (茶碗01直径約13cm) 茶碗01直径約13cm

Content ID:1529672

  • 1,452
This material collection includes materials that can be used in Studio Mode. (What is Studio Mode?)
This material catalog contains materials that can only be used on Windows and Mac (Intel) systems.

It is a model made for the test. There are more and more differences in the shape of PAINTEX but with the use of 3DTL. It is only a difference of the appearance a little different from the PRO. テスト用に作ったモデルです。ほぼ一緒の形状ですがPAINTEXの3DTLを使用すると違いがでますます。PROだとちょっと見た目が違うくらいの違いでしかないです。

Operation Confirmation CLIP STUDIO PAINT (EX) 1.3.2


The behavior is at CLIP STUDIO PAINT 1.3.2. ACTION is not confirmed.
The internal 3D model is used for the CMO form surface.

It is a rice bowl.

[Material Collection Contents]
  • The bowl 01A_ diameter about 13cm high 6cm_TX
  • The bowl 01B_ diameter about 13cm high 6cm_TX
  • The bowl 01C_ diameter about 13cm high 6cm_TX


The difference is that the shape of the edges is slightly different.


A is the most pointed edge, and B is rounded inside.
C is rounded inside and outside. It is also just a little low in height.
(The diagram is a state of the Contour setting 1 to make it visible)





The difference between settings on MODELER
A is a side of the edge, the outside with a sharp line
Only the outside of the edge of B is a sharp line
C is not an acute angle line with the inside outside of the edge.
(Edge is the part that the Orange arrow points)
* It is not a material that can be opened in MODLER and edited.


[PAINT EX]
There is a difference in the 3DLT of the line.
It may be good to have a foreground or a distant view, depending on the size on the canvas.

Refer to the material description for samples and details.


動作確認 CLIP STUDIO PAINT (EX) 1.3.2


動作はCLIP STUDIO PAINT 1.3.2時点のものです。ACTIONでの動作確認はしていません。
内部の3Dモデルはcmo形式   曲面化利用

飯茶碗です。

【素材集内容物】
  • 茶碗01A_直径約13cm高約6cm_TX
  • 茶碗01B_直径約13cm高約6cm_TX
  • 茶碗01C_直径約13cm高約6cm_TX


違いは、フチの部分の形状が少しずつ違います


Aが一番エッジが尖っていて、Bは内側が丸みを帯びています。
Cは内側と外側も丸みを帯びています。また、ほんの少しだけ高さが低いです。
(図は見えやすいように輪郭線の設定1の状態です)





MODELER上での設定の違いは、
Aはフチのが内側、外側ともに鋭角線
Bはフチの外側だけ鋭角線
Cはフチの内側外側ともに鋭角線ではありません。
(フチとはオレンジ矢印が指す部分です)
※MODLERで開いたり、編集できる素材ではありません。


【PAINT EX】
3DLTの場合の線の出方に違いがでます。
近景や遠景、キャンバス上のサイズによって使い分けるといいかもしれません。

見本や詳細は各素材説明を参考にしてください。


Category 1 カテゴリ1

Content ID:1529672

Published : 10 years ago

Last updated : 7 years ago

clouddrift's profile Go to profile

コンテンツID:1270866→ID:1272409へ再掲しました。