Climbing playground equipment (bouldering, log climbing pier) (クライミング遊具(ボルダリング、丸太の登り桟)) クライミング遊具(ボルダリング、丸太の登り桟)

Content ID:2310991

  • 261
  • Free
This material can be used in Studio Mode. (What is Studio Mode?)

It is a triangular mountain-shaped climbing playground equipment made of logs. Width 2.4m, depth 2.2m, height 1.5m. The front is a planked bouldering surface with 27 holds in seven colors. The back side is a climbing pier with thin logs passed at equal intervals, and you can go up and down with your legs crossed. No matter which way you climb from, you can exit to the other side at the top. At the top is a log to grasp. The boards are stretched one by one, so the joint line comes out as it is. Since the board, hold, log fence, and framework are object separate, only the hold can be erased and bare planking can be used. The origin is the center of the contact patch, and the bouldering surface is -Y. Comes in 4 angles. 丸太で組んだ三角の山型クライミング遊具です。幅2.4m、奥行2.2m、高さ1.5m。正面は板を張ったボルダリング面で、7色のホールドが27個付いています。裏面は細い丸太を等間隔に渡した登り桟で、こちらは足を掛けて上り下りします。どちらから登っても頂上でもう片方へ抜けられる形です。頂点には掴まるための丸太を通してあります。板は1枚ずつ張ってあるので、目地の線がそのまま出ます。板面・ホールド・丸太の桟・骨組みは別オブジェクトなので、ホールドだけ消して素の板張りにもできます。原点は接地面の中心、ボルダリング面は−Y向き。4アングル入り。

About this material

It is a triangular climbing playground equipment with a width of 2.4m and a height of 1.5m. The way of climbing is different on the front and back.

The table shows the bouldering surface

On a slope with 7 boards, there are 27 holds of 7 colors. The angle of the slope is about 54 degrees. The boards are stretched one by one, so the joints come out as lines.

The back is a climbing pier

Thin logs of φ70 are passed in 8 tiers at intervals of about 230 mm. It is a surface where you hang your legs and go up and down. You can exit to the front side at the top.

Vertex

There is one log threaded through the apex. Nothing sticks out in front of the bouldering surface. The frame is a ridge log φ150, a diagonal material φ130, and a base φ130. The wood mouth is chamfered, and the wooden side where the growth rings can be seen is put in another material.

4 angles

Four items are registered: front, back, right, and left.

LT Conversion

Below is the main line converted to LT with the actual CLIP STUDIO machine.

Specifications

  • Width 2,400 × Depth 2,200 × Height 1,500mm / Slope angle approx. 54 degrees
  • Bouldering surface: 7 boards, 27 holds (7 colors, separate object)
  • Log pier: φ70 in 8 steps (spacing approx. 230mm)
  • Frame: ridge log φ150, diagonal material φ130, base φ130 (wood mouth is tree ring material)
  • 4 angles (front, back, right, left)
  • Origin: Center of contact patch / Bouldering surface: −Y orientation

この素材について

幅2.4m・高さ1.5mの三角のクライミング遊具です。表と裏で登り方が違います。

表はボルダリング面

板を7枚張った斜面に、7色のホールドが27個付きます。斜面の角度は約54度。板は1枚ずつ張ってあるので、目地が線として出ます。

裏は登り桟

φ70の細い丸太を8段、約230mm間隔で渡してあります。足を掛けて上り下りする面です。頂上で表側へ抜けられます。

頂点

頂点に丸太を1本通してあります。ボルダリング面の手前には何も突き出しません。骨組みは稜の丸太φ150、斜材φ130、土台φ130。木口は面取りしたうえ、年輪の見える木口面を別のマテリアルで入れてあります。

アングル4件入り

正面・背面・右・左の4件を登録してあります。

LT変換

下はクリスタの実機でLT変換した主線です。

仕様

  • 幅2,400 × 奥行2,200 × 高さ1,500mm/斜面の角度 約54度
  • ボルダリング面:板7枚張り・ホールド27個(7色・別オブジェクト)
  • 丸太の桟:φ70を8段(間隔 約230mm)
  • 骨組み:稜の丸太φ150・斜材φ130・土台φ130(木口は年輪マテリアル)
  • アングル4件(正面・背面・右・左)
  • 原点:接地面の中心/ボルダリング面:−Y向き

Material マテリアル

  • default material 初期マテリアル

Configuration 配置

  • default layout 初期レイアウト

Angle アングル

  • Front 正面
  • The backside 背面
  • Right 右
  • Left 左

Update history

2026/10/4 Material review to improve accuracy, angle registration to improve convenience.      * This is a successor and revision of the triangular climbing playground equipment (bouldering surface + log climbing pier) [old ID 2298337].      * It is a new material because the update due to model correction failed. We apologize for the inconvenience, but please download it again. 2026/10/4 正確性向上のため素材見直し、利便性向上のためアングルの登録。
     ※三角のクライミング遊具(ボルダリング面+丸太の登り桟)[旧ID 2298337]の後継・改訂版です。
     ※モデル修正に伴う更新に失敗しため新規素材となっております。お手数ですが再ダウンロードお願いします。

Content ID:2310991

Published : 3 hours ago

Last updated : 3 hours ago

Didymoi.A's profile Go to profile

興味をもっていただきありがとうございます! 私は漫画家をやっています。漫画で利用する素材などをBlenderを使って作成しています。たくさんアップしますのでフォローお願いします。Xでも制作過程を乗せていますのでフォローやいいねなど反応していただけると嬉しいです。また仲良くしていた方限定で制作要望を承る場合がありますのでダイレクトメッセージください。