Assembly perspective [3-point perspective +] (組み立てパース【3点透視＋】) 組み立てパース【3点透視＋】

Content ID：2177230

- Report to administrator

30 CLIPPY

渡季

Translated by

This is an additional material collection specialized for three-point perspective of the previous "Assembled Perspective Grid". Please use it together with the previous work. 前作の「組み立てパースグリッド」の3点透視に特化した追加素材集です。前作と合わせてご使用下さい。

In addition to the previous work "Assembled Perspective Grid", it was made for the purpose of improving the usability of three-point perspective.

The usage method is almost the same as the previous work, but if you use the [horizontal] of this work as horizontal 1 and horizontal 2 as opposed to the [vertical] perspective of the previous work, you will be able to create a perspective that spreads downward like an overhead view.

The CP is the same as the CP on the center line of the screen, and it is used in the form of placing the "center circle" of width 1 and width 2 on the vertical line with the "center circle" of the vertical perspective.

(The one where the "center circle" of the horizontal perspective overlaps will be HL in this case)

* Since it is a perspective with HL on one side of the screen, this image material is named "one-sided" for convenience.

For details, please see the explanation of the previous material collection "Assembly Perspective Grid".

Example of use: 3-point perspective grid (overhead view)

Procedure (1) Select one of the [Vertical] of the previous work "Assembly Perspective Grid" and drag and drop it around the center of the canvas.

Step (2) Select one of the "one side [horizontal]" of this material collection and drag and drop it upward on the vertical line with the "center circle" of the vertical perspective.

Fine-tune with the arrow keys so that the center line of the vertical perspective passes through the center of the "center circle"

(At this time, it is good to align the upper and lower positions of the image to some extent.)

Toward the "center circle" added in steps (3) and (2), drag and drop "one side [horizontal]" as the other and side 2.　

Change "Edit" ≫ "Transform" ≫ "Flip Left" in the menu bar and change "layer color" to pink or something else

If you need to correct the position, "zoom in, reduce, rotate" and make fine adjustments with the arrow keys to overlap the "center circle".

Step (4) Put the three layers in one folder and scale them all at once to fit the canvas.

* When enlarging or shrinking, it refers to "fixed aspect"

A perspective grid with three-point perspective using one-sided perspective is complete!

* This work can also be rotate image to support "horizontal canvas" and "agitated perspective", but you need to be careful when choosing the orientation and layer color when combining.

Basically, put together the things made according to the above procedure and rotate them 180 ° to "Perspective"

Combining two pieces of this work [vertical] against the previous work [horizontal], it should become a "horizontal canvas" by rotating 90 ° or -90 °.

前作「組み立てパースグリッド」に追加して、3点透視の使い勝手を良くする目的で作りました。

使用方法は前作とほぼ変わりませんが、前作の【縦】パースに対して、今作の【横】を横1と横2にして使用すると、俯瞰図らしい下への広がりのあるパースを作ることが出来るようになります。

画面の中心線上をCPとすることは変わらず、「縦パースの『中心の円』の乗った縦線上」に横1と横2の『中心の円』を配置する形で使用します。

（横パースの『中心の円』が重なる方がこの場合のHLになります）

※画面の片側にHLが寄ったパースなので、こちらの画像素材には便宜上『片側』と名前を付けています

詳しくは前作素材集「組み立てパースグリッド」の解説をご覧下さい。

使用例：3点透視パースグリッド（俯瞰）

手順①　前作「組み立てパースグリッド」の【縦】を一枚選んでキャンバスの中心辺りにドラッグ＆ドロップします

手順②　こちらの素材集の「片側【横】」を一枚選び、縦パースの『中心の円』の乗った縦線上の上方にドラッグ＆ドロップします

『中心の円』の中心に縦パースの中央線が通るように方向キーで微調整します

（この時、画像の上下の位置もある程度合わせておくとよい）

手順③　②で追加した方の『中心の円』に向かって、「片側【横】」をもう一枚、横2としてドラッグ＆ドロップします