It will be updated within this year.
2018.11
Arranges multiple image data.
Can arrange up to 5 rows of x4 columns.
<年内中にアップデート予定です>
2018.11
複数の画像データを並べます。
最大5行x4列の整列が可能です。
It is a auto action very convenient but..., it あり is a little difficult.
Also, it is not suitable for printing. Mainly for the web.
-Introduction ●
Please register the downloaded "illustration-arranging" auto action.
You can register with import material set on the menu of the auto action palette.
If you select "button mode" on the menu of the auto action palette, you can click the button to run it.
(If you want to delete or edit auto action, deselect "button mode". )

● How to use ●
Perform "① Canvas creation" auto action with no single canvas

Canvas (2400x3000px) has been executed.
You'll see a grid of one mass 600x600px.

Run the "Open ② image file" auto action.
(OK even if you open the file normally)
Image file (PNG, JPEG, etc.) remains open...
When "③ paste position is selected from the bottom", the illustration is pasted at the specified position.
(Many pieces are stacked in the same position.) More layers

!! Attention!
この The Auto Action of this sticking position is that when you press the button continuously, "Illustration arranging- five rows four columns" canvas disappears.
Open image → paste position auto action → open image → paste position auto action... please repeat.
(It is safe to save the canvas frequently)

I get this error message.
It doesn't take long to start again.
● Two rows of two columns
If there are few illustrations to line up, you can select the range to fit the grid and crop (canvas size match the selection).

Also auto action to delete the line is included ●

I want to reduce the image (margin), I want to draw a border
I registered the auto action for illustration only.
https://assets.clip-studio.com/ja-jp/detail?id=1727684
とても便利そうなオートアクションですが・・・、いささか難ありです。
あと、印刷には不向きです。おもにweb用です。
●はじめに●
ダウンロードした「イラストならべ~る」オートアクションを登録してください。
オートアクションパレットのメニューにある「セット素材を読み込み」で登録できます。
オートアクションパレットのメニューにある「ボタンモード」にしておくと、ボタンをクリックすれば実行します。
(オートアクションを削除したり編集する場合は、「ボタンモード」を解除してください。)

●使い方●
キャンバスがひとつも無い状態で、「①キャンバス作成」オートアクションを実行

キャンバス(2400x3000px 解像度350px)が実行されました。
1マス600x600pxのグリッドが表示されます。

「②画像ファイルを開く」オートアクションを実行。
(普通にファイルを開いてもOK)
画像ファイル(png、jpegなど)を開いたまま・・
「③貼り付け位置を下から選んで実行」すると、指定した位置にイラストが貼り付けられます。
(同じ位置に何枚も重ねられます。レイヤーが増えます)

!!注意!!
この貼付け位置のオートアクションは、連続でボタンを押すと「イラストならべ~る5行4列」キャンバスが消滅してしまいます。
画像を開く→貼り付け位置オートアクション→画像を開く→貼り付け位置オートアクション・・・・を繰り返してください。
(こまめにキャンバスを保存しておくと安心です)

↑こんなエラーメッセージが出ます
最初からやり直しても、時間はかかりませんが・・
●2行2列の場合●
並べるイラストが少ない場合は、グリッドにあわせて範囲選択してトリミング(キャンバスサイズを選択範囲にあわせる)すればOK。

●行を削除するオートアクションも入ってます●

●画像を小さくしたい(余白)、罫線を引きたい●
「イラストならべ~る専用【余白と罫線】」オートアクションを登録しました。
https://assets.clip-studio.com/ja-jp/detail?id=1727684