Subtle gaps that don't notice
A gap not closed in the close gap
It is a auto action that can be used at such time
気づかない微妙な隙間
隙間閉じでは閉じてくれない隙間
そんな時に使えるオートアクションです
I'll try create ground of this
There is a gap
Normal fill
The close gap has the largest gap and is not fail well.
auto action created
Even if there is a gap, it is fail painted.
There's no problem in the gaps.
= = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Use
Select the line drawing layer you want to create ground
Note, at this time, if the line is sticking out of the layer, the action cannot be performed well.
In that case, please close the lines.
This is OK
Take action
Until the gap part is filled with (thick) line width habit (thin and OK even a little) spread
Fit the value you just entered in the line-width habit (thin)
It's okay to take a little bigger at this time. Please try to adjust to your liking.
It's okay to take a little bigger at this time. Please try to adjust to your liking.
Action Complete
(Originally from layer color converted to white)
Weakness
A sharp jagged fill may protrude
Improved weaknesses (~ Kai)
Please adjust the close gap of the advanced fill (area surrounded by black) according to the condition of Giza.
Just good example of the condition of Giza at 6, 0
0 3
I think that the finer the detail, the smaller the lower the amount of Giza.
I posted a final improvement version.
When there is a line drawing dirt and irregularity, unevenness stood out and measures were made.
Last
Improved version
Added final A
[Improvement]
[Improvement]
Adjust the size of the waste.
-Supports a wider gap
No need to adjust line width
-No automatic pallet color change
これの下地を作成してみます
隙間があります
通常の塗りつぶし
隙間閉じが最大でも隙間があり上手く塗りつぶせていません
作成したオートアクション
隙間があっても塗りつぶせています
気づかない隙間も問題なしです
======================
【使い方】
下地を作成したい線画レイヤーを選択します
注、この時、線がレイヤーからはみ出していると上手くアクションを実行できません
その場合は線を書き足し閉じておいてください
これでOKです
アクションを実行します
線幅習性(太)で隙間部分が埋まるまで(薄くてちょっとでもOK)広げます
線幅習性(細)で先ほど入力した値(太)に合わせます
この時(太)とり少し大きくても大丈夫ですお好きに調整してみてください
この時(太)とり少し大きくても大丈夫ですお好きに調整してみてください
アクション完了です
(本来はレイヤーカラー変換から白になっています)
【弱点】
鋭いギザギザは塗りつぶしがはみ出す場合があります
弱点を改善しました(~改)
ギザの具合に合わせて「高度な塗りつぶし(黒に囲まれた部分)」の隙間閉じを調節してください
2,0でちょうどいいギザ具合例
0.3
ギザが細かく狭いほど値を小さくするといい気がします
最終改善版を投稿しました
線画み汚れやムラがある場合凸凹が目立ちましたので対策しました
前回
改善版
最終Aを追加しました
〈改善点〉
〈改善点〉
・ゴミ取の大きさを調整
・さらに広い隙間に対応
・線幅調整必要なし
・パレット色の自動変更を無し
Category 1 カテゴリ1