It is a material for sci-fi prisons and prison facilities.
It will be the material in the detention zone where the cells are lined up. By connecting or diverting it, it is possible to make it a larger or smaller facility to some extent.
Basically, it is built as a prison, but I think it can be used as a factory, some kind of facility, research institute, religion-related, hotel, spaceship ship, etc.
The cells themselves are not object in detail, so if necessary, please purchase materials only for the cells in the private room (sold separately) separately.
It is a three-story structure. The cell is set up like tempered glass instead of an iron bar. If necessary, please add reflected light or nets as appropriate.
The entrance to the camp has a large door. It is manual, but it can be opened and closed. The windows are lined up in a setting with something like a surveillance and control room at the top.
It has a T-shaped structure and there is a passage at the end of the door.
There are shutters at the back of the left and right passages, which can be opened and closed manually. It is assumed that you can enter and exit from here to another living area and carry-in vehicles.
Next to the door is a small room like a monitoring and control room, which is designed to be paired on the left and right.
The 1st and 3rd floors are double rooms with bunk beds, and the 2nd floor is only 1 bunk bed.
It is troublesome, but it can be replaced. Each room is a separate object with a passage. In addition, the object of only one floor, which is pre-connected to the cells on the floor, is also attached as a bonus, so please edit it well and use it.
Stairs are installed in the front and rear corners, respectively. You can adjust the size of the facility itself by reducing the number of rooms or shifting the back wall to the front.
As shown on the right side of the figure below, parts that are one-sided walls are also included, so it can be used as a cell facility on only one side.
Inside the cell. There are only beds and toilets.
* You may feel the weight depending on the performance of the PC. I think it will be easier to move by hiding the object to some extent and moving it.
Prices are subject to change without notice. Thank you for your understanding.
Sci-fi cell sold separately. The left and right walls, ceiling, floor, back wall, bed and toilet are object separately, so if you need detailed scenes in the room, you can use this to change the line of sight, composition, and make it easier to customize the facility itself.
* This is sold separately. Please be careful.
==================================
* Wall unit included in the cell
==================================
* This is sold separately. Please note that it is not included.
SF系の刑務所、監獄施設の素材です。
監房がずらりと並んだ収容区内の素材となります。 連結したり流用することである程度はもっと大きな施設にしたり小さくすることも出来ます。
基本的には監獄として作っていますが、工場であったり、なにかしらの施設、研究所、宗教関連、ホテル、宇宙船の船内などとしても使用できるかと思います。
監房自体は細かくオブジェクト分けをしておりませんので、必要な場合は別売の個室の監房のみの素材を別途お求めください。
3階建ての構造となっています。 監房は強化ガラス的なものが鉄格子代わりになっているような設定です。必要に応じて適宜反射光や網などを加筆などして下さい。
収容区の入り口は大きな扉があります。手動となりますが開閉可能です。 上部に監視、コントロールルーム的なものがある設定で窓が並んでいます。
T字の構造になっており、扉の先には通路があります。
左右の通路の奥にはシャッターがあり、手動で開閉可能です。こちらから別の居住区であったり搬入の車両など出入りをすることが出来るような想定です。
扉横には監視、コントロールルーム的な小部屋が左右に対である設計になっています。
1階、3階が2段ベッドの二人部屋、2階が1段のベッドのみとなっています。
面倒ですが入れ替え可能です。 部屋は一つずつ通路込みの独立したオブジェクトになっています。 また階の監房をあらかじめ連結した1つの階のみのオブジェクトもオマケで付けていますので、うまく編集してお使いください。
階段は前方と後方の角にそれぞれ設置しています。 部屋を減らしたり、奥の壁を手前にズラしてくることで施設自体のサイズ感を調整することができます。
下図の右側のように一面壁となっているパーツも同梱していますので片側だけの監房施設としても使用できます。
監房内部です。ベッドとトイレのみの設備となっています。
※PCの性能により重さを感じる場合があります。ある程度オブジェクトを非表示にして動かすことで動かしやすくなると思います。
価格は予告なく変更致します。ご了承願います。
別売りのSci-fi 監房です。こちらは左右の壁、天井、床、奥の壁、ベッドやトイレなどが別オブジェクトになっていますので、室内の細かなシーンが必要な場合や、こちらを使い、視線、構図の変化や、施設自体のカスタマイズもしやすくすることが出来ます。
※こちらは別売りのものです。ご注意ください。
==================================
※監房に同梱の壁ユニット
==================================
※こちらは別売りのものです。同梱されていませんのでご注意ください。