Dandelions with small diameters (小径のタンポポたち) 小径のタンポポたち

Content ID:2250368

  • 361
  • Free
This material can be used in Studio Mode. (What is Studio Mode?)

These are dandelions, plantains, and trefoils that grow on the roadside of small paths. Created in Blender.
The number of vertices is 195,557, which is a lot. Both sides of the path can be moved with the plants, respectively. Dandelions and plantain can also be moved one by one.
There are 18 groups of 70~80 trefoils in one group. Each can be moved in groups.
The overall size is about 1.7m×3.2m and 20cm high.
小径の道端に生えるタンポポ、オオバコ、三つ葉です。Blender で作成しました。
頂点数が195,557で多めです。道の両サイドはそれぞれ植物と一緒に移動できます。タンポポとオオバコは1本づつ移動することも可能です。
三つ葉は70~80本をひとつのグループとして18グループあります。それぞれグループ単位で移動可能です。
全体の大きさは面積1.7m×3.2m、高さ20cm程度です。

 This is the result of the object and LT conversion read by CLIP STUDIO.

LT conversion conditions:

extract line conditions paper size A4 horizontal 600dpi, vector layer
Line width 2px, detection accuracy 60, outer border emphasis 10, smooth level 1

Two parallel lights are used. The intensities are 1.2 and 0.9, respectively.

Since the leaves and the ground are created in a flat surface, please turn off (uncheck) the backface culling to display the back side. Backface sculling can be set from "→sub tool detail", "Environment" → "rendering settings". (There is an image at the bottom of this page)





This is an image with tone work enabled.

(Texture extract line is disabled.) )


This is an image with tone work and texture extract line enabled.


Both sides can be moved together with the plants, so they can be lined up on one side as shown in the image. The small diameter part is also stacked one at the bottom, so you can lengthen the two sheets vertically.






One four-leaf mixture is mixed in one group of trefoils.


object list.


This is an expanded list of ground side 1 (as well as ground side 2).


Since the leaves and the ground are created in a flat surface, please turn off (uncheck) the backface culling to display the back side. Backface sculling can be set from "→sub tool detail", "Environment" → "rendering settings".



 クリスタで読み込んだオブジェクトとLT変換の結果です。

LT変換の条件:

ライン抽出条件 用紙サイズ A4横 600dpi、ベクターレイヤー
 線幅 2px, 検出精度 60、外枠線強調度 10、スムース レベル 1

平行光を2つ使用しています。強度はそれぞれ 1.2, 0.9 です。

葉や地面は平面で作成していますので、裏面を表示するためにバックフェースカリングを off(チェックを外す)にして下さい。バックフェースカリングの設定は「サブツール詳細」→「環境」→「レンダリング設定」からできます。(このページの下の方に画像があります)





トーンワークを有効にした画像です。

(テクスチャのライン抽出は無効にしています。)


トーンワークとテクスチャのライン抽出を有効にした画像です。


両サイドは植物と一緒にそれぞれ移動できますので、画像のようにひとつのサイドに並べることができます。小径の部分も下に1枚重ねてあるので、2枚縦にならべて長くすることができます。






三つ葉のひとつのグループごとに1本四つ葉が混じっています。


オブジェクトリストです。


地面サイド1を展開したリストです(地面サイド2も同様)。


葉や地面は平面で作成していますので、裏面を表示するためにバックフェースカリングを off(チェックを外す)にして下さい。バックフェースカリングの設定は「サブツール詳細」→「環境」→「レンダリング設定」からできます。



Material マテリアル

  • default material 初期マテリアル

configuration 配置

  • default layout 初期レイアウト

Content ID:2250368

Published : 8 hours ago

Last updated : 8 hours ago

平面組立屋's profile Go to profile

 趣味で 3D の景観、オブジェクトを作成しています。主に使用しているソフトは Terragen と Blender です。火星の景観など天文・宇宙関係のイラストを描いてみたかったので適当なソフトを探していたところフリーで使えるこの2つが見つかりました。一般の風景画にもジャンルを広げています。Blender で作成したオブジェクトがクリスタでも利用できることからクリスタでのイラスト作成も始めました。