Castle gate with drawbridge (跳ね橋つき城門) 跳ね橋つき城門

Content ID：2216008

- Report to administrator

200 CLIPPY

めろんぽー

This material can be used in Studio Mode. (What is Studio Mode?)

Translated by

The drawbridge is angled at 0°, 30°, 60° and 90°.
You can also open and close the gate and raise and lower the drop grate. 跳ね橋は0°、30°、60°、90°の角度が付きます。
門の開閉や落とし格子の上下もできます。

Number of vertices: Approx. 24,000

Vertex count: approximately 24,000.

I created it with an assumed scale of 1/5, so I think it will fit better if you make your character 1/5 the size.

Even so, it is large when placed normally, so if you make it smaller with the "object scale", you can make it the size you want. (The bottom is placed on A4 paper)

Since this was created at a 1/5 scale, your character should fit nicely if you set their size to 1/5 as well.

Even so, the model may still appear a bit large when placed as is, so you can easily adjust it to your preferred size using the “Object Scale” option.
(The example below shows it placed on an A4 sheet.)

pose parts

Click "pose parts Presets" in the red circle in the figure below.

Movable Parts

Click the “Movable Parts Preset” button shown in the red circle in the image below.

gate_door You can open and close → castle gates. 　This part is designed to open and close.

yard_door Doors on the back left and right of the building can be opened → closed. This part is designed to open and close.

iron_fence You can go up and down → the trap grate on the arch of the gate. This part can move up and down.

gate_bolt Because the gate kannuki → hidden by default

Make the angle of view visible behind the gate
gate_bolt_on with layout presets
Move gate_bolt bars with pose parts presets

You can move it with.

★ When opening the gate, set it to "default layout" in the layout preset. (Because when the gate opens, the kannuki remains in the middle)

Below is the state gate_bolt_on in "Layout Preset"

gate_bolt

By default, this part is hidden.
To make it move, please follow these steps:

Adjust the camera so you can see the back side of the gate.
Set the layout preset to “gate_bolt_on.”
In the movable parts preset, move the “gate_bolt” bar.

★ When opening the gate, please switch the layout preset back to “Default Layout.”
(Otherwise, the latch will remain in the center when the gate opens.)

The image below shows the gate with the layout preset set to “gate_bolt_on.”

→ drawbridge moves to 0° (default), 30°, 60°, and 90° angles.

drawbridge_30 and chain_30 correspond.

The drawbridge can be adjusted to 0° (default), 30°, 60°, or 90°.

The settings “drawbridge_30” and “chain_30” correspond to each other.

If you want it to be 30°

Adjust with the drawbridge_30 bar in "pose parts Presets"

Use the “drawbridge_30” bar in the Movable Parts Preset to adjust it.

In addition, it is adjusted with the bar on the chain_30.

Next, use the “chain_30” bar to fine-tune the adjustment.

Adjust 60° and 90° using the same number drawbridge and chain bars.

For 60° and 90°, use the matching drawbridge and chain bars to adjust them.

drawbridge 90°

Coat of arms crest

By default, a frame for the coat of arms is displayed.

If you don't need a frame, click crest_off in "Layout Presets".

The crest frame is shown by default.
If you’d like to hide it, just select “crest_off” in the Layout Preset.

大きなオブジェクトで分けているので、描きこみ辛いときは動かせます。

The object is split into large parts, so you can move them around if it’s hard to work on the details.

LT変換の設定例

Example settings for LT conversion

変換後

After conversion

気に入っていただけたら嬉しいです。

I hope you like it.

頂点数　　　約24,000

Vertex count: approximately 24,000.

想定スケールを1/5にして作成したので、ご自分のキャラクターを1/5の大きさにすると収まりが良くなるかと思います。

それでも普通に配置すると大きいので、『オブジェクトのスケール』で小さくすると好きな大きさにできます。（下はA4用紙に配置した状態）

Since this was created at a 1/5 scale, your character should fit nicely if you set their size to 1/5 as well.

可動パーツ

下図の赤丸部分の『可動パーツのプリセット』をクリックしてください。

Movable Parts

Click the “Movable Parts Preset” button shown in the red circle in the image below.

gate_door お城の門→開閉できます。　This part is designed to open and close.

yard_door 建物の裏左右にある扉→開閉できます。This part is designed to open and close.

iron_fence 門のアーチにある落とし格子→上下できます。This part can move up and down.

gate_bolt 門のかんぬき→初期設定では非表示なので

門の裏側が見える画角にする
レイアウトのプリセットでgate_bolt_onにする
可動パーツのプリセットでgate_boltのバーを動かす

で動かすことができます。

★門を開けるときはレイアウトのプリセットで『初期レイアウト』にしてください。（門が開くとかんぬきが真ん中に残ってしまうため）

下は『レイアウトのプリセット』でgate_bolt_onにした状態

gate_bolt

By default, this part is hidden.
To make it move, please follow these steps:

Adjust the camera so you can see the back side of the gate.
Set the layout preset to “gate_bolt_on.”
In the movable parts preset, move the “gate_bolt” bar.

★ When opening the gate, please switch the layout preset back to “Default Layout.”
(Otherwise, the latch will remain in the center when the gate opens.)

The image below shows the gate with the layout preset set to “gate_bolt_on.”

drawbridge 跳ね橋→0°(初期設定)、30°、60°、90°の角度に動きます。

　　　　　　　drawbridge_30とchain_30が対応しています。

The drawbridge can be adjusted to 0° (default), 30°, 60°, or 90°.

The settings “drawbridge_30” and “chain_30” correspond to each other.

30°にしたい場合