【Limited time 20CP】Semicircle console table (【期間限定20CP】半円コンソールテーブル) 【期間限定20CP】半円コンソールテーブル

Content ID:2159149

  • 40
This material can be used in Studio Mode. (What is Studio Mode?)

It is a semicircular console table that can be placed by the wall or in the hallway.
With LT conversion, the lines come out neatly and can be used with little addition.
Easy to illustrate in colored 3D. With commentary.
壁際や廊下に置ける半円型のコンソールテーブルです。
LT変換で線が綺麗に出て加筆が少なく使用できます。
色付き3Dで簡単にイラスト化できます。解説付き。


Drawers do not open.
It is 85 cm high, 95 cm wide and 45 cm deep. It was placed at 175 cm for men and 160 cm for women.
* The wall and bottle used are listed as separate materials.


Explanation of color illustration

1. First, place the 3D and decide the angle, etc.

2. Layer duplicate the placed 3D, uncheck "Light source: This model is apply light source" from the 3D tool property, and rasterize the 3D layer.

3. From the tool property of the 3D layer you left, check whether "Light source: This model is apply light source" is checked, adjust the direction of the shadow, etc., and change the light source intensity if you are concerned.
Select "Pure White for Shadows" from the 3D layer materials.

4. Use 3D layer LT conversion to add lines and shadows. Change the line width and line detection amount according to the illustration size.
Check the tone to make it only one color in gradation. Here we toning a net, but it can be gray.

5. Change the color of the line produced by LT conversion to your liking, take the selection from the tone produced by one color, and layer the shadow with your favorite color.
It is completed together with the color rasterize in step 2.
Finally, I added white as an extra.

引き出しは開きません。
高さは85㎝、横約95㎝、奥行き約45㎝です。男性175cm、女性160cmで配置しました。
※使用している壁と瓶は別素材として出品しています。


カラーイラスト化の解説

1.まず3Dを配置して角度などを決めます。

2.配置した3Dをレイヤー複製して、3Dツールプロパティから「光源:このモデルは光源の影響を受ける」のチェックを外し、3Dレイヤーをラスタライズします。

3.残してあった3Dレイヤーのツールプロパティから「光源:このモデルは光源の影響を受ける」のチェックが入っているかを確認して影の向きなどを調整、光源強度も気なる場合は変更してください。
3Dレイヤーのマテリアルから「影用真っ白」を選びます。

4.3DレイヤーのLT変換で、線と影をいれます。線幅と線の検出量はイラストサイズによって変更してください。
トーンにチェックを入れて、階調化で1色のみにしてください。ここでは網トーン化していますが、グレーでも構いません。

5.LT変換で出した線の色をお好みで替えて、1色で出したトーンから選択範囲を取り好きな色で影を重ねます。
2でラスタライズしたカラーと合わせて完成です。
最後におまけでホワイトを入れてみました。

material マテリアル

  • color カラー
  • for shadowspure white 影用真っ白

disposition 配置

  • default layout 初期レイアウト

Content ID:2159149

Published : 6 hours ago

Last updated : 6 hours ago

杉浦里's profile Go to profile

プロアシスタントしています。仕事で作った3D等をアップしていきたいと思っています。