This material may contain sensitive content. (See rating guidelines
Would you like to view the material anyway?

Condom Bottom Open (コンドーム底開き) コンドーム底開き

Content ID:1896137

  • 945
  • 100 GOLD
  • 1,000 CLIPPY
This material can be used in Studio Mode. (What is Studio Mode?)
This material may contain sensitive content. (See rating guidelines


※ Sorry for the update immediately.
Because the circle part of the contents of the individual packing was too small, it corrected it....
I also put a label on the surface.


* Expected hike to 50G/500CP.

It is a 3D model of the condom of the bottom opening box with twelve pieces.

The box is set in the open from the beginning.

Only the upper surface of the outer box is designed with a simple it ish design. The other side and the individual packing are solid colors.

Because the outline is thick in the initial state, I hide it, and adjust it, please.

The layout of two and six in the layout preset 12 pieces and 6 pieces,
The lid is completely closed.



The simple model of the prop that the packing is connected two to five steps from the bottom to the second.
The top two movements are individual models with uneven surfaces.
For this reason, it is hard to use two or more out.

The top one is nested and you can move it together.



The LT conversion is tough if the detection accuracy is not high about 100 to 90. There is no line drawing for individual packing.
The surface label is "texture extract line", only when the irregularity is turned on "tone work".
(When the surface label is not required, turn off the extract line of the texture.) )

Because the shadow of the individual packing is not easy to come out, please rotate the sphere of the light source and adjust it so that the shadow comes out well.
Please do good luck because it is considerably difficult depending on an honest angle....
(Worst, it is output to pieces only in the box and the individual packaging that hides the packaging,
Please select only in the box and fit the individual wrapping. )

Even if it collapses, it looks it if it is properly corrected.



Since the second stage after the prop is required to retouch depending on the angle.



※早速のアップデート申し訳ございません。
個包装の中身の円部分が小さすぎたので修正しました…。
ついでに表面にラベルも入れました。


12個入りで底開き箱のコンドームの3Dモデルです。

箱は最初から開いた状態でセットしてあります。

外箱の上面だけは簡単なそれっぽいデザイン付き。それ以外の面と中の個包装は無地です。

初期状態では輪郭線が太いので非表示にするか調整して下さい。

レイアウトプリセットには12個入りと6個入りで2つずつのレイアウトと、
フタが完全に閉じたものがあります。



個包装は下から5段目までが前後2つ繋がったハリボテの簡易モデル、
一番上2つだけは個別に動き、表面に凹凸があるモデルです。
このため2つ以上外に出して使うのは厳しいです。

一番上つは入れ子になっていて一緒にも動かせます。



LT変換では検出精度は100~90程度と高くないと厳しいです。個包装には線画が出ません。
表面のラベルは「テクスチャのライン抽出」を、凹凸は「トーンワーク」をオンにした時のみ出ます。
(表面のラベルが不要な時はテクスチャのライン抽出をオフにして下さい。)

個包装の影は出にくいので、光源の球を回転させて上手く陰影が出るように調整して下さい。
正直角度によってはかなり難しいので頑張って下さい…。
(最悪、個包装を非表示にした箱と個包装のみでバラバラに出力し、
箱の中だけ選択して個包装をはめ込みして対応下さい。)

↓潰れてしまっても適当に加筆すればそれっぽく



2段目以降がハリボテなので角度によっては加筆必須となります。


Material マテリアル

  • Material マテリアル

disposition 配置

  • 12 out of 1 12個1
  • 12 out of 2 12個2
  • 6 out of 1 6個1
  • 6 out of 2 6個2
  • default layout 初期レイアウト

Update history

2022/02/01 Packaging fixes 2022/02/01 個包装の修正

Old version

Content ID:1896137

Published : 3 years ago

Last updated : 3 years ago

horitora's profile Go to profile

アップや無料期間を逃したくない方はTwitterのフォローをお願いします■価格は需要や他素材とのバランス等を鑑み、告知無しに変動します。■ブログにおすすめ素材や価格帯によるまとめ、類似素材の比較、3Dデッサン人形の2人ポーズの合わせかた等、クリスタ関係の便利なトピック等色んなお役立ち記事があるので、是非覗いてみてください!(プロフィールページ→ヘッダー右下のアイコンから)