It is 3D of the raising and lowering window for the indoor side. The color is for the LT conversion for visibility.
Please be careful because there is not a lock and a hook that has simplified considerably.
The backside cannot be used. The windows are working. (Both moves, but it is a specification to move the bottom. )
I have made a reference to the standard values of the UK. (※ It is a standard because it was mixed by the source.) )
The ceiling height is 2.4 m in general housing, and 2.7 m in a large floor and a small shop in the living room
We assume 3m or more at a medium or more store.
From floor to window sash to one of about 46, 76, 91, 107cm
Seems to be a common fit. (Ft, in)
This is 2.7 m height of the ceiling (wall), 60cm on the sash,
Sash under is about 46cm (large), 76cm (Medium), 107cm (small) three species.
The number of files is four because only 107cm has two kinds of split number of Windows 6 and 8.
Because it distributes three by the height difference of the ceiling (wall), please choose it according to the application.
Size comparison figure. (The sofa is a separate distribution material, 3D doll is 175cm. )
I do it side by side with a ceiling height by each level under a sash.
2.7 m and 2.4 m is not a large difference (about 10cm difference in height of the window), because the rail of the ceiling is movable, I think either one is enough.
LT conversion diagram
What was the LT conversion by connecting the three ↓ size to the side by side?
Width 4m, 2m of the wall included, 4m is displayed in the initial state.
When I want to arrange the window sideways, the wall interferes when I keep it.
Please hide the 4m wall and duplicate it and move it from 80cm to 100cm.
↓ Illustrated (image is a different material)
Hides 4m from the object list.
Select the object and copy and paste, "position" of the "X" of the [×] one of 80 ~ 100 (cm),
If the other one is-80 to 100, it will connect nicely. If you want to increase further, as well!
※ It is good that you can simply hide the wall, but it is careful because a little depth comes out to the window.
It can be used with the wall 3D series distributed by ★. (Figure is another material)
The material is stuck in the same position (paste button on the bottom of the material pallet, or paste
Align placement > position value).
Hide other than "panel" and "Rail" in "wall 3D".
(Rails can be used to hide the window and use the wall.) )
Because it interferes with the window except "small", it hides the one and converts it separately,
Remove the portion of the wall towards the window where the area is selected and the wall is wearing.
室内側用の上げ下げ窓の3Dです。色は可視性の為でLT変換用。
だいぶ簡略化していてロックやフックもないのでご注意ください。
裏面は使えません。窓は稼働。(どちらも動きますが下を動かす仕様です。)
UKの標準値を参考に作成しました。(※ソースによりまちまちだったので目安です。)
天井の高さは一般住宅が2.4m、リビングなど広いフロアや小規模店舗で2.7m、
中規模以上の店舗で3m以上と想定しています。
床から窓サッシまでの高さは約46、76、91、107cmのいずれかに
合わせるのが一般的なようです。(ft,inを換算)
こちらは天井(壁)の高さ2.7m、サッシ上約60cm、
サッシ下が約46cm(大)、76cm(中)、107cm(小)の3種。
107cmだけ窓の分割数が6と8の2種あるのでファイル数は4つです。
天井(壁)の高さ違いで3つ配布しているので、用途に応じて選んでください。
サイズ比較図。(ソファは別配布素材、3D人形は175cm。)
サッシ下の高さごとに天井高別で横並びにしてします。
2.7mと2.4mは大差がなく(窓の高さ約10cm差)、天井のレールは可動なので、どちらか片方で十分だと思います。
LT変換図
↓3サイズを横並びに繋げてLT変換したもの
それぞれ幅4m,2mの壁付属で、初期の状態では4mが表示されています。
窓を横に並べたい時はそのままだと壁が干渉してしまうので、
4mの壁を非表示にして複製、左右に80cm~100cmずらして下さい。
↓図説(画像は別素材)
オブジェクトリストから「4m」を非表示にします。
オブジェクトを選択してコピペし、「配置」の「位置」の「X」を片方80~100(cm)、
もう片方は-80~100にすると、綺麗に繋がります。更に増やしたい場合も同様に!
※単純に壁を非表示にしても良いですが、窓に少し奥行きが出てしまうので注意です。
★別配布の「壁3D」シリーズと併用可能です。(図は別素材)
素材を同じ位置に張り付け(素材パレット下部の貼り付けボタンで張り付けるか、
「配置」>「位置」の値を揃える)。
「壁3D」の「パネル」「レール中」以外を非表示にする。
(レールは窓の方を非表示にて壁の方を使用しても大丈夫です。)
「小」以外は窓と干渉してしまうので、片方を非表示にして別々に変換し、
窓の方の壁を範囲選択→壁の方の被っている部分を削除して下さい。
3D up and down Windows 2.7 m 3D上下窓2.7m