Tsuki_Fude (Tsuki_Fude) Tsuki_Fude

Content ID：1759205

17,679

- Report to administrator

Free

たなかもげたろう

Translated by

Update information

2019/12/8

The noise when the line was drawn slowly, and the ink at the end when the line was drawn was reduced.

Kaze_Fude of brush pen style brushes that I made before

https://assets.clip-studio.com/ja-jp/detail?id=1726964

It becomes a sister article of.

It is a brush that can draw a beautiful line as opposed to a Kaze_fude.

Grazed can be expressed according to the pressure, speed, and inclination of the pen.

(Color setting for the layer required)

The influence of the inclination is large, and the grazed is easy to come when I draw it at an angle near perpendicular.

The maximum value when drawn strongly in proportion to the brush size changes.
If you want to make an extreme expression, you should take a small brush size if you want to draw a large, average line.

Too much brush size greatly delays the environment.

Adjust the size of your use to your environment.

(More than 300 dpi, brush size is recommended 100pix below)

Notes

If you write in black and white, the layer will not be reflected when you grazed black and white from the beginning.

The avoidance method is as follows.

1. Draw anything at once to the target layer.

2. Change the layer property without erasing the content.

3. After changing the layer property to monochrome, erase the contents of the drawing and you are ready to finish.

Also, if you apply "color in preview" after the change, the effect of the Caspar will not be reflected in the line thereafter.

The application of the expression color, please the illustration, or after drawing up the line drawing.

Update infomation
2019/12/08

Improving drawing performance.
Reduced the noise generated when drawing a line slowly.

Revalancing color depth.
(Mainly, "End of Drawing Line")

Tsuki_Fude is the brush in contrast to Kaze_Fude I made before.
It makes you possible to draw a clean line.

If you want to draw a clean line. Set layer mode to "Color layer".
Tsuki_Fude provide a beatiful gradient effect to drawing line in this layer mode.

When you change layer mode to "monochromatic". Then you can get scratch effect instead of gradient effect.
Scratch effect mainly controlled by drawing speed and tilt.

Try to use it carefully.
The larger brush size, the more latency.
Recommend brush size is
Less than 100 pixel, canvas resolution is
300 dpi or above.

Notice
------------------------------------------------------------
Scratch effect doesn't work when you use brush on "Monochromatic layer" from first.
You need to draw to "Color layer", and switch to "Monochromatic layer" to avoid the issue.
------------------------------------------------------------

Thank you for downloading Tsuki_Fude!
I Hope this brush helps you.
Have fun!

アップデート情報

2019/12/8

線をゆっくり描いた場合のノイズ、線を描いた際の終わり際の墨だまりを軽減しました。

以前作った筆ペン風ブラシのKaze_Fude

https://assets.clip-studio.com/ja-jp/detail?id=1726964

の姉妹品になります。

Kaze_fudeとは対照的に綺麗な線も描くことができるブラシです。

筆圧や速度、ペンの傾きに応じて掠れの表現ができます。

(要レイヤーの表現色設定)

傾きの影響が大きく、垂直に近い角度で描くと掠れが出やすくなります。

ブラシサイズに比例して強く描いた際の最大値が変わります。
極端な表現をしたい場合はブラシサイズを大きく、平均した線を描きたい場合は小さく取ってください。

ブラシサイズを大きく取りすぎると環境により大きく遅延が出ます。

利用するサイズを環境に合わせて調整してください。

(解像度は300dpi以上、ブラシサイズは100pix以下がおすすめです)

※注意事項

モノクロで書く場合、最初からレイヤーをモノクロにすると掠れが反映されません。

回避方法は以下の通りです。

1.対象レイヤーに一度、何でもいいので描きます。

2."描いた内容は消さずに残したまま"レイヤープロパティを変更します。

3.レイヤープロパティをモノクロに変更後、描いた内容を消して準備完了です。

また、変更した後に"プレビュー中の表現色"を適用すると、それ以降はカスレの効果が線に反映されません。

表現色の適用はイラスト、または線画を描き上げた後にお願いします。

update infomation
2019/12/08

Improving drawing performance.
Reduced the noise generated when drawing a line slowly.

Revalancing color depth.
(mainly,"End of drawing line")

Tsuki_Fude is the brush in contrast to Kaze_Fude I made before.
It makes you possible to draw a clean line.

If you want to draw clean line. Set layer mode to "Color layer".
Tsuki_Fude provide a beatiful gradient effect to drawing line in this layer mode.

When you change layer mode to "monochromatic". then you can get scratch effect instead of gradient effect.
Scratch effect mainly controlled by drawing speed and tilt.

Try to use it carefully.
the larger brush size,the more latency.
recommend brush size is
less than 100 pixel,canvas resolution is
300dpi or above.

Notice
------------------------------------------------------------
Scratch effect does not work when you use brush on "Monochromatic layer" from first.
You need to draw to "Color layer"once,and switch to "Monochromatic layer"to avoid the issue.
------------------------------------------------------------

Thank you for downloading Tsuki_Fude!
I hope this brush helps you.
Have fun!

Old version