Men's Sweatshirt A Light Edition / sweatshirt_mens_A_Light (メンズスウェットシャツAライト版／sweatshirt_mens_A_Light) メンズスウェットシャツAライト版／sweatshirt_mens_A_Light

Content ID：2183459

3,892

- Report to administrator

Free

ERi_Kanzawa

This material can be used in Studio Mode. (What is Studio Mode?)

Translated by

This is a light version of the sweatshirt 3D that I exhibited recently.
This is a light version of the “Sweatshirt 3D” model I released earlier.

... Full version ▷ https://assets.clip-studio.com/ja-jp/detail?id=2182157

Base ... 172cm ／ B:87.4 ／ H:84.6 ／ W:62.6
△:40,792

▽ The texture has an extra shadow. It is a diluted version of the full Material: Jersey.
The composition of the polygons does not change.

The texture includes only some light shading, just as a bonus.

It's a simplified version of the full material, "Material: Jersey."

Polygon layout is the same as the full version.

The differences between the full version and the lite version are as follows:
・ Presence or absence of the back side such as sleeves and collar
・ 1 type of texture → 5 types
The red part becomes the part without polygons.

Here are the main differences between the light and full versions:

・ Inner sides (like inside the sleeves or collar) are not included
・ 1 texture in the trial version → 5 textures in the full version
The red parts in the preview image show the areas without polygons.

Pose material can be adapted, but must be corrected by hand.
In addition, there is a limit to the range of motion, such as the shoulders and buttocks.

You can apply pose materials, but some manual adjustments will be needed.
Please note that the range of motion is limited, especially around the shoulders and hips.

▽ Because the experiment was created, the gap between the sleeves and hem when the joints are bent is poor.
Correct the gaps using the stamp tool or the distortion tool.

Since this was created as an experiment, there may be some gaps around the sleeves and hem when the joints are bent.
You can fix these using tools like the stamp or warp tool.

▽ If you like, buy the full version! ＞v＜

If you like it, please check out the full version too! :

→ Full version ▷ https://assets.clip-studio.com/ja-jp/detail?id=2182157

I may raise the price after a while.
I hope you like it. -ｖ-

The price may go up after a while.
I hope you like it!

...

この間出品したスウェットシャツ3Dのライト版です。
This is a light version of the “Sweatshirt 3D” model I released earlier.

...Full version ▷ https://assets.clip-studio.com/ja-jp/detail?id=2182157

Base ... 172cm ／ B:87.4 ／ H:84.6 ／ W:62.6
△:40,792

▽テクスチャはおまけ程度の影がついてます。完全版の「マテリアル：Jersey」を薄めたものです。
　ポリゴンの構成は変わらないです。

The texture includes only some light shading, just as a bonus.

It's a simplified version of the full material, "Material: Jersey."

Polygon layout is the same as the full version.

▽完全版とライト版の違いは以下の通りです。
　・袖や襟など裏側の有無
　・テクスチャが1種類 → 5種類
　赤い部分がポリゴンのない部分になります。

Here are the main differences between the light and full versions:

　・ Inner sides (like inside the sleeves or collar) are not included
　・ 1 texture in the trial version → 5 textures in the full version
The red parts in the preview image show the areas without polygons.

▽ポーズ素材の適応はできますが、手打ちでの修正が必要です。
　また、肩や臀部などの可動域に限度があります。

You can apply pose materials, but some manual adjustments will be needed.
Please note that the range of motion is limited, especially around the shoulders and hips.

▽実験がてら作成したため、関節を曲げた際の袖や裾の隙間が拙いです。
　生じた隙間はスタンプツールや、歪みツールを用いて修正してください。

Since this was created as an experiment, there may be some gaps around the sleeves and hem when the joints are bent.
You can fix these using tools like the stamp or warp tool.

▽よかったら完全版も買ってね！＞v＜

If you like it, please check out the full version too! :

→ Full version ▷ https://assets.clip-studio.com/ja-jp/detail?id=2182157

しばらくしたら値上げするかもしれないです。
気に入っていただけたら嬉しいです。-ｖ-

The price may go up after a while.
I hope you like it!

...

body ボディ