It is a free sample of the material collection Choi balloon.
Please use to confirm the usability.
The regular version has nine balloons and nine brush types.
(Pending)
素材集 ちょいフキダシ の試供品です。
使い勝手の確認にご利用ください。
正規版は、フキダシ 9 種、ブラシ 9 種です。
(申請中)
Please check the details of the material in the regular version.
Here is customize way.
● Initial setting
The junction is at the bottom left, and the pattern is clockwise from there to the brush tip.
The order in which you registered.
You can check the registration status of the pattern in sub tool detail → brush tip.
You can customize the base by deleting or moving.
Deformation of the pattern
You can change the brush tip → thickness.
Initial setup: 100
Left: 50 horizontally to the right: 50 in the vertical direction
Presence of Groundwork
You can change it in the balloon line and base.
Sample
All [a few Choi] customize the balloon.
I think I can do a lot more.
- Half tone of the base
When you change the layer property → expression color → monochrome 》 to Gray,
You will be able to manipulate the "bubble" and "opacity of the base".
Initial setup: 100
Toning of the groundwork
"Layer property → effect → tone" on the setting screen is out.
Be sure to select the concentration → use brightness of image.
The following is set to "dot settings → cross" to make the sample easy to see.
You can change the balance of the base opacity and the number of tone lines.
- Edge of the whole speech balloon
"Layer property → effect → edge" on, the setting screen is out.
Customize of Tones
There is a variety of tones in the dot settings.
The pattern of the tone can be rotated by the number of "angle".
- Color
If you select layer property → expression color → color, each property
You will be able to color.
Please try various.
Attention
If you combine, the joint part becomes delicate state.
Tail 》 is not supported. Drawing collapses (sample left)
Please cover in a different layer (sample right)
Please understand.
There is no brush because it is a free sample. (Available in the regular version)
If you want to draw with a brush, we recommend a vector that can be customize after drawing.
素材の詳細は正規版でご確認ください。
以下はカスタマイズ方法です。
● 初期設定
接合部は左下にあり、そこから時計回りにパターンが《ブラシ先端》に
登録した順に並びます。
《サブツール詳細→ブラシ先端》でパターンの登録状態が確認できます。
削除や移動でベースをカスタマイズできます。
● パターンの変形
《ブラシ先端→厚さ》で変更できます。
初期設定:100
左:水平方向に 50 右:垂直方向に 50
● 下地の有無
《フキダシ→線・下地》で変更できます。
サンプル
すべて【ちょいフキダシ-もこ1】をカスタマイズしたものです。
もっと色々できると思います。
● 下地のハーフトーン
《レイヤープロパティ→表現色→モノクロ》を《グレー》に変更すると、
《フキダシ→下地の不透明度》が操作できるようになります。
初期設定:100
● 下地のトーン化
《レイヤープロパティ→効果→トーン》オンで設定画面が出ます。
必ず《濃度→画像の輝度を使用》を選択してください。
以下は《網の設定→クロス》に設定して、サンプルを見やすくしています。
《下地の不透明度》と《トーン線数》の数値で、バランスを変更できます。
● フキダシ全体のフチどり
《レイヤープロパティ→効果→フチ》オンで、設定画面が出ます。
● トーンのカスタマイズ
《網の設定》に様々なトーンがあります。
《角度》の数値でトーンの柄を回転できます。
● カラー
《レイヤープロパティ→表現色→カラー》を選択すれば、各プロパティで
彩色できるようになります。
色々お試しください。
● 注意
《結合》すると、接合部分が微妙な状態になります。
《しっぽ》には対応していません。描画が崩れます(サンプル左)
別レイヤーでカバーをお願いします(サンプル右)
以上、ご了承ください。
試供品なのでブラシはありません。(正規版にはあります)
ブラシで描画する場合は、描画後のカスタマイズができるベクターを推奨します。
Balloon Ti フキダシ